Repeat steps 1 to 4 to remove the second transit bolt. Packaging materials are not children's toys. For your safety and to comply with electrical regulations, seek professional advice if you want to install your machine in a bath or shower room. Select a space at least 60cm wide, 60cm deep and 85cm high. Also leave enough space to open the door fully, so that you can load and unload it easily. Take care when you move the machine not to rip any floor coverings. The weight of the machine may cause indentations in some floor coverings.
Your machine will be noisy if the two front feet are not adjusted so that the machine stands firm and level. Move your machine into its final location, taking care not to trap or kink the hoses. Turn one or both front feet. When adjusting the feet, use a spirit level to check the machine stands level, from side to side and from front to back. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the machine.
Remember: please use the new hoses supplied, fitted to the machine. Old hoses may cause leaks due to worn out washers or may be split due to water pressure. Remember: This is a cold-fill machine Before making connections to the cold water supply, allow the water to run freely from the supply tap until it is perfectly clear. Make sure there are no kinks or bends in the hose. The water pressure at the supply tap must be within the values indicated in the Technical Details table see page If the water inlet hoses are not long enough, you can purchase an extended hose from Hotpoint Service on Always use a new inlet hose.
Check the water inlet hose at least once a year, replace if cracked as worn hoses could split under water pressure. Turn on the water supply and check that the connections do not leak. If there is a leak, turn off the water supply, disconnect the hoses and check that the sealing washers are in place. Refit the hoses and turn on the water supply. If this is not the case, replace the socket or the plug, ensuring a 13A fuse is fitted. The machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.
When the machine is installed, the mains socket must be within easy reach and should be connected to a suitable electrical supply. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman. The company denies all liability if and when these standards are not respected. Once the appliance has been installed and before you use it for the first time, run a wash cycle without detergent and no laundry.
This will check your installation, connections and drainage and will thoroughly clean the interior before you carry out an actual wash programme on your laundry. During this cycle check for any leaks from under the machine.
If present ensure all hoses are securely tightened. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Please check your email for further instructions. Enter a new password. STEP 1 Electrical Guide Choose a location for your washing machine, where possible on a solid floor, with the electrical sockets and water supply taps easily accessible. Allow sufficient space: mm width, m depth and mm height.
DO NOT install in a bath or shower room. STEP 3 Dispenser Drawer Read through this section to familiarise yourself with the different compartments within the dispenser drawer. STEP 5 Using your Machine How to start your selected programme and how to stop or change the programme if so required. STEP 6 Options Guide All available optional wash features are explained within this section - These allow you to adjust your selected wash programme to suit your needs.
DO NOT overload the washing machine. Troubleshooting Please refer to the Troubleshooting section if you have any problems when using your washing machine.
There may be nothing wrong! Keep this Book in a safe place for quick reference. Fuses Your appliance comes fitted with a plug and a 13 amp 13A fuse. Changing the Mains Lead If you have damaged the existing lead and need a new one, contact Hotpoint Service UK on: or www. Seek professional advice if you need to use an extension lead. Changing the Plug If you need to change your plug, if it does not fit your socket: isolate the machine from the mains supply.
STEP 2 Installation. Failure to do so may cause damage to your machine! Use a crosshead Unscrew the STOP when 3 Hold, slide screwdriver to remove the bolt using a threads can be across and pull plastic cover. It is important the transit bolt and spacer come out intact see pic. Old hoses may cause leaks due to worn out washers or may split due to water pressure. Hot and Blue Hose end to Cold. Replace any Max. If you have no hot water supply The spring on each foot will stop them coming loose.
NOTE: The mains cable must only be replaced by an authorised serviceman. Drawer release latch 2. Pre-wash detergent compartment Maximum ml powder or ml liquid 3. Main detergent compartment Maximum ml powder or ml liquid 4. Programme times listed in the Programme Table are approximate.
Before using your machine make sure that the two transit bolts and spacers have been removed see Installation Guide. Any electrical work necessary to install this machine should be carried out by a qualified electrician. Do not plug your machine into a socket when your hands are wet. Page Service Service Before calling the Service Centre: Use the troubleshooting guide to see if you can solve the problem yourself see Troubleshooting.
If not, turn off the machine and call the Service Centre closest to you. You will be charged for a service engineers visit if a problem with your machine is caused by incorrect installation or misuse.
Print page 1 Print document 16 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account?
0コメント